<dd id="eyukf"></dd>

    <em id="eyukf"></em>

        <tbody id="eyukf"><noscript id="eyukf"></noscript></tbody>
        PC(聚碳酸酯)EXL6013/沙伯基礎(SABIC)

        PC(聚碳酸酯)EXL6013/沙伯基礎(SABIC)_價格_物性_圖片_UL黃卡

        公司主營產品:耐高溫塑料,耐低溫塑料,耐磨塑料,耐熱塑料,耐寒塑料,防火塑料,加纖塑料,醫療級/食品級塑料,抗紫外線塑料,紅外線穿透塑料...

        全國24小時銷售熱線:

        0769-83023208

        產品詳情

        ?            SABIC(沙伯基礎創新塑料)LEXAN PC EXL6013是專為要求具有高沖擊性能和優于標準聚碳酸酯的耐化學性的應用而開發的。

        以下是SABIC沙伯基礎創新Lexan PC EXL6013中英文物性表資料:

        PROPERTIES TYPICAL VALUESUNITSTEST METHODS
        MECHANICAL



        Taber Abrasion, CS-17, 1 kg
        10mg/1000cySABIC method
        Tensile Stress, yield, 50 mm/min
        55MPaISO 527
        Tensile Stress, break, 50 mm/min
        60MPaISO 527
        Tensile Strain, yield, 50 mm/min
        7%ISO 527
        Tensile Strain, break, 50 mm/min
        100%ISO 527
        Tensile Modulus, 1 mm/min
        2100MPaISO 527
        Flexural Stress, yield, 2 mm/min
        80MPaISO 178
        Flexural Modulus, 2 mm/min
        2150MPaISO 178
        Ball Indentation Hardness, H358/30
        90MPaISO 2039-1
        IMPACT



        Izod Impact, unnotched 80*10*3 +23°C
        NBkJ/m2ISO 180/1U
        Izod Impact, unnotched 80*10*3 -30°C
        NBkJ/m2ISO 180/1U
        Izod Impact, notched 80*10*3 +23°C
        70kJ/m2ISO 180/1A
        Izod Impact, notched 80*10*3 -30°C
        60kJ/m2ISO 180/1A
        Charpy 23°C, V-notch Edgew 80*10*3 sp=62mm
        75kJ/m2ISO 179/1eA
        Charpy -30°C, V-notch Edgew 80*10*3 sp=62mm
        70kJ/m2ISO 179/1eA
        Charpy 23°C, Unnotch Edgew 80*10*3 sp=62mm
        NBkJ/m2ISO 179/1eU
        Charpy -30°C, Unnotch Edgew 80*10*3 sp=62mm
        NBkJ/m2ISO 179/1eU
        THERMAL



        Thermal Conductivity
        0.2W/m-°CISO 8302
        CTE, 23°C to 80°C, flow
        7.E-051/°CISO 11359-2
        CTE, 23°C to 80°C, xflow
        7.E-051/°CISO 11359-2
        Ball Pressure Test, 125°C +/- 2°C
        PASSES-IEC 60695-10-2
        Vicat Softening Temp, Rate B/50
        138°CISO 306
        Vicat Softening Temp, Rate B/120
        140°CISO 306
        HDT/Be, 0.45MPa Edgew 120*10*4 sp=100mm
        131°CISO 75/Be
        HDT/Ae, 1.8 MPa Edgew 120*10*4 sp=100mm
        122°CISO 75/Ae
        PHYSICAL



        Mold Shrinkage on Tensile Bar, flow
        0.6-0.8%SABIC method
        Density
        1.2g/cm3ISO 1183
        Water Absorption, (23°C/saturated)
        0.35%ISO 62-1
        Moisture Absorption (23°C / 50% RH)
        0.15%ISO 62
        Melt Volume Rate, MVR at 300°C/1.2 kg
        5cm3/10 minISO 1133
        ELECTRICAL



        Volume Resistivity
        >1.E+15Ohm-cmIEC 60093
        Surface Resistivity, ROA
        >1.E+15OhmIEC 60093
        Dielectric Strength, in oil, 3.2 mm
        17kV/mmIEC 60243-1
        Relative Permittivity, 1 MHz
        2.7-IEC 60250
        Dissipation Factor, 50/60 Hz
        0.001-IEC 60250
        Dissipation Factor, 1 MHz
        0.01-IEC 60250
        Comparative Tracking Index
        175VIEC 60112
        Relative Permittivity, 50/60 Hz
        2.7-IEC 60250
        FLAME CHARACTERISTICS



        Glow Wire Flammability Index 850°C, passes at
        1mmIEC 60695-2-12
        Injection Molding



        Drying Temperature
        120°C
        Drying Time
        2-4hrs
        Maximum Moisture Content
        0.02%
        Melt Temperature
        290-320°C
        Nozzle Temperature
        280-310°C
        Front - Zone 3 Temperature
        290-320°C
        Middle - Zone 2 Temperature
        280-310°C
        Rear - Zone 1 Temperature
        270-300°C
        Hopper Temperature
        60-80°C
        Mold Temperature
        80-120°C



        上一篇:PC(聚碳酸酯)EXL5429/沙伯基礎(SABIC)

        下一篇:PC(聚碳酸酯)EXL1444/沙伯基礎(SABIC)

        欣隆全塑膠
        相關產品

        Related products

        推薦產品
        日韩男同GAY片免费